Cách đo áp suất buồng đốt?

phong38
phong38
Bình luận: 30Lượt xem: 11,272
maquina

maquina

Thành viên O-H
1-Apague el encendido y el sistema de inyección de combustible antes de realizar una prueba de compresión. La mayoría de los fabricantes recomiendan calentar el motor durante la prueba 1
2-Place the throttle plate in a fully open position to allow an unlimited amount of air to enter the cylinders during the test
3-Remove all spark plugs from the engine
4-Connect a remote start button to the boot system
5-There are many types of compression gauges available. The type of screw tends to be the most accurate and easy to use
6-Carefully install the meter in the spark plug hole of the first cylinder
7-Connect a battery charger to the car to allow the engine to start at constant and normal speeds needed to obtain accurate test results
8-Press the remote start button and observe the indicator reading after the first revolution of the engine
9-Allow the engine to rotate four revolutions and observe the reading after the fourth. The reading should increase with each revolution
10-Observed readings must be recorded. After all the cylinders have been tested, a comparison of the cylinders can be made
11-Before removing the meter from the cylinder, release the pressure from the cylinder using the meter release valve
12-Each cylinder must be tested in the same way
13-After completing the test on all cylinders, compare them. If one or more cylinders are much lower than the others, continue testing those cylinders with the wet test
14-Pour a small amount of oil into the weak cylinder (s)
15-Reinstall the compression gauge on that cylinder and perform the test
16-If the reading increases with the presence of oil in the cylinder, the most likely cause of the low original readings was a poor sealing of the piston ring. Using oil during a compression test is usually called a wet test
 
Cai banh xe

Cai banh xe

Kích thích nghĩa là kích vào chỗ người ta Thích!
maquina đã viết:
1-Apague el encendido y el sistema de inyección de combustible antes de realizar una prueba de compresión. La mayoría de los fabricantes recomiendan calentar el motor durante la prueba 1
2-Place the throttle plate in a fully open position to allow an unlimited amount of air to enter the cylinders during the test
3-Remove all spark plugs from the engine
4-Connect a remote start button to the boot system
5-There are many types of compression gauges available. The type of screw tends to be the most accurate and easy to use
6-Carefully install the meter in the spark plug hole of the first cylinder
7-Connect a battery charger to the car to allow the engine to start at constant and normal speeds needed to obtain accurate test results
8-Press the remote start button and observe the indicator reading after the first revolution of the engine
9-Allow the engine to rotate four revolutions and observe the reading after the fourth. The reading should increase with each revolution
10-Observed readings must be recorded. After all the cylinders have been tested, a comparison of the cylinders can be made
11-Before removing the meter from the cylinder, release the pressure from the cylinder using the meter release valve
12-Each cylinder must be tested in the same way
13-After completing the test on all cylinders, compare them. If one or more cylinders are much lower than the others, continue testing those cylinders with the wet test
14-Pour a small amount of oil into the weak cylinder (s)
15-Reinstall the compression gauge on that cylinder and perform the test
16-If the reading increases with the presence of oil in the cylinder, the most likely cause of the low original readings was a poor sealing of the piston ring. Using oil during a compression test is usually called a wet test
Nhấn để mở rộng...
Bác viết gì vậy ạ, xem không hiểu? Chắc là tiếng Pháp
 
Nguyễn Xuân Giang

Nguyễn Xuân Giang

Giữ xe
Nhân viên
maquina đã viết:
1-Apague el encendido y el sistema de inyección de combustible antes de realizar una prueba de compresión. La mayoría de los fabricantes recomiendan calentar el motor durante la prueba 1
2-Place the throttle plate in a fully open position to allow an unlimited amount of air to enter the cylinders during the test
3-Remove all spark plugs from the engine
4-Connect a remote start button to the boot system
5-There are many types of compression gauges available. The type of screw tends to be the most accurate and easy to use
6-Carefully install the meter in the spark plug hole of the first cylinder
7-Connect a battery charger to the car to allow the engine to start at constant and normal speeds needed to obtain accurate test results
8-Press the remote start button and observe the indicator reading after the first revolution of the engine
9-Allow the engine to rotate four revolutions and observe the reading after the fourth. The reading should increase with each revolution
10-Observed readings must be recorded. After all the cylinders have been tested, a comparison of the cylinders can be made
11-Before removing the meter from the cylinder, release the pressure from the cylinder using the meter release valve
12-Each cylinder must be tested in the same way
13-After completing the test on all cylinders, compare them. If one or more cylinders are much lower than the others, continue testing those cylinders with the wet test
14-Pour a small amount of oil into the weak cylinder (s)
15-Reinstall the compression gauge on that cylinder and perform the test
16-If the reading increases with the presence of oil in the cylinder, the most likely cause of the low original readings was a poor sealing of the piston ring. Using oil during a compression test is usually called a wet test
Nhấn để mở rộng...

where do you live?
 

Bạn hãy đăng nhập hoặc đăng ký để phản hồi tại đây nhé.

Đăng nhập liền nha, dễ lắm

Đã ghim

Cà phê OH

Cà phê OH

#cafe-oh
Hội anh em sửa chữa ô tô

Hội anh em sửa chữa ô tô

#hoi-mau-nhiem-nhot

Chủ đề bác đang quan tâm

Bên trên